为耽误了打码机使用寿命短，提高 法宝使用率和无缺率，大幅度(du♛)降低瑕疵率。现将我子公司打码机常人保护性及医养小知识与巨匠推荐。
In order to prꦏolong the service life of the jet ꧋printer, improve the utilization rate and intact rate of the equipment, and reduce the failure rate. Now we share our daily maintenance and maintenance knowledge with you.
一、喷码机平常利用注重事变：
1. Notices for the daily use of jet printers:
1、因打标机充分利用的印(yi🍸n)刷油墨和精浓剂很是瞬间熄火，言于须在典范漏风处打理打标机，一别易燃易爆、燃烧和靜電。
1. Because the ink and🔴 diluent used in the🀅 jet printer are very easy to burn, it is necessary to place the jet printer in a well-ventilated place, away from fire, flame and static electricity.
2、最好不要遗留问题uv墨水൲(shui)🔴、洗濯剂净泡过的碎布和碎纸条在喷码(ma)器旁。
2. Do not leave any ink, cloth and paper pieces soaked in detergent beside the𒁃 printer.
3、 严防在打码(ma)机两侧抽食烟，应吊件“禁止炊火”和“易燃物uv油墨”标上在打码(ma)机两侧(ce🌜)。
3. Smoking is strictly prohibited near the printer. The signs of "No Fireworks" and "Flammable 🌠Ink" should be hung near the printer.
4、在激光打码机周边合理安排二阳极氧化碳灭兵器图片（借喻远每隔10米）。
4. Place a carbon dioxide fire extinguisher near the⛦ jet printer (the longest distance i🤪s 10 meters).
二、喷码(ma)发电机气毗连注重细节事变
II. Notices𝐆 for Electrical Connection of Jet Coder
1、 接入220V单相电原（含地线），必定利用率(♐lv)原装电原线，毗连到坚固的☂、装备有地线的电原排插上。
1. When connected to 220V single power su😼pply (including ground wire), the original power supply cable must be used and connected to a fixed power socket with ground wire.
2、 ♍地线(xianไ)的毗连需制定制度关与规定。要是地线打战不好，有都可以建立打码机芯片组的受到破坏或触发其他的替伏分险。
2. The connection of ground wires must comply with the relevant regulations of the state. If the ground wire contact is not good, it may cause damage to the printeꦬr motherboard or other potential hazards.
三、都是确保医养重要性事变
3. Daily maintenance matters needing attention
1. 通过打码机印刷油墨、精提剂时对杜绝配戴隐身眼睛。
1. It is absolutely forbidden to wear contact lenses when using ink and diluent of jet p🍌rinter.
2. 当增大胶印油墨或浓缩造成(cheꦚng)剂使用时，号召通过抗溶液橡胶手套和防防镜。
2. Anti-solveওnt gloves and protective goggles are recomm💟ended when adding ink or diluent.
3. 手持喷码(ma)机常人安养线程池接下来：
3. The daily maintenance process of the jet printe🎃r is as follows:
上海打码机保护性保养首也不压缩空气管、花洒头保(bao๊)养：
Maintenance of Beijing Printer is🐠 mainly pipeline and nozzle maintenance.
a) 墨囊更行：先将管道里的墨囊全数抽暇，高浓剂注射到墨囊罐工作1h后全数 欺负，其次插足高浓剂工作0.5h后全数欺负，插足原厂装配的墨囊。呼吁机械设备每再生利用率年 关闭程序一起墨囊更行，服务裝(z🐬huang)备工作两倍一致。（排空的电镀废水不呼吁2次再生利用率，防备止进行管道梗塞） a) 激光喷嘴洗濯：对不具备着拒绝洗濯功能主治的手持喷码机，呼吁天天有电开关机时洗濯，以 为了确保机选取高道德的复印机结局。在激光喷嘴左上方让袋子，用通用洗瓶裝入高浓剂(j💎i)，机瞄激光喷嘴、笔记本充电极、查重极、高压电偏转板上的墨渍关闭程序洗濯，要注意不能让高浓剂溅原装进口眼及新皮肤，洗濯清扫后，拿纸巾将激光喷嘴各个部位件的洗濯剂擦水。
(a) Ink renewal: first, all the ink in the pipeline 🔯is exhausted, diluent is injected into the ink tank 𒀰for 1 hour, then all the ink is discharged after adding diluent for 0.5 hours, and then the original ink is added. It is suggested that the machine be updated once a year to ensure more stable operation of the equipment. (Waste liquid extracted is not recommended for secondary use in order to avoid pipeline blockage.) a) Sprinkler cleaning: For the sprinkler without automatic cleaning function, it is recommended that the machine be cleaned when switched on and off every day to ensure high quality printing effect. First, place the container under the sprinkler head, fill the diluent with a special bottle, clean the ink stains on the nozzle, charging electrode, detection electrode and high-pressure deflection board. Take care not to let the diluent splash into the eyes and skin. After cleaning, wipe the cleaning agent of all parts of the sprinkler head with a paper towel.
b) 调济墨线：若研制成功墨线背离收受接手器，停掉激光喷咀买通，用共用洗瓶插足少 许浓缩造成剂至激光喷咀帽，接连买(♔mai)通3次左右，如墨线不停在一致实力地位则需停掉酬金缓解喷腔。墨线规范性：直对收受接手器查看苹果手机，墨线喷入收受接手器七分中之一处且略左。（侧看墨线在收受(sho♑u)(shou)接手器正中间间）
B) Adjust ink line: If the ink line deviates from the reclaimer, the nozzle should be opened first, a little diluent should be added to the nozzle 🍌cap with a special washing bottle, and the nozzle cap should be opened three times or so repeatedly. If the ink line is always in the same position, the nozzle cavity should be adjusted artificially. Ink standard: Looking at the recycler, ink is sprayed into one third of the recycler and slightly left. (Look sideways at the ink line in the middle of the receiver)
二）激光打码机永劫间停用后💃的保护性 其中1次停用，尽管那时候不是，只需该激光打码机在每周7天内重启工作2次，并翻阅墨🅘(mo)线最高继承工作或吸塑油游戏更新某个h，允许便都可以用什么次短停用更换永劫间的停用。
2) Maintenance of any downtime of the jet printer after a long downtime, regardless of the length of time, as long as the jet printer runs twice a week, and opens the ink line to run continuously or ink updates for at least one hour, it can replace the lo🙈ng downtime with several short downtime.
1）喷码(ma)器停机之时为8-♋十天：对喉管和打印机花洒头停机每次洗濯，打印机花洒头朝上规划，以避免(mꦐian)蓝墨水流回。
1) Inkjet printer shutdown time is 8-15 days: the throat and nozzle are cleaned once, the nozzle is placed u🧸pward to prevent ink reflux.
2）打标机宕机之前转变五天：这时肯定将自动化设备内的打印墨囊排放出后插足精提剂日常运转(zh꧃uan)，终了后把喷枪朝上计划，解决办法打印墨囊分流。
2) The stop time of th✨e printer is more than 15 days. At this time, the ink in the machine must be 💖discharged and run with diluent. After that, the sprinkler head should be placed upward to prevent the ink from flowing back.
3）永劫间关机后打火打标机看重事变(💝bian) 关机8-30多天打标机的打火，若有应该要，核查了解墨线始终不变性。已停𝔍(ting)次430分钟的喷头买通。
3) Start the printer after a long downtime. Notes: Start the printer 8-30 days after the downtime. If necessary, check the stability of th♌e ink line. Make a 5-minute nozzle pass.
4)欠费当时超过30天
4) Over 30 days of downtime
将线路中的吸塑油放气。插足浸提咖啡剂正常的工作部分时，疏浚因永劫间变慢时而梗塞的(d🎉e)线路。浸提咖啡剂正常的工作时可变慢1次五半个小时的雾炮买通。浸提咖啡剂正常的工作终了后放气线路，插足新吸塑油，再买通雾炮3半个小时使墨线价值倍加不会改变。
Empty the ink in the pipeline. Add diluent and run for one hour to dredge the blocked pipeline due to long shutdown. 🍨When the diluent is running, the nozzle can be opened for 5 minutes at a time. After the diluent is running, the drainage pipe is emptied, new ink is added, and the nozzle is opened for 3 minutes to make the ♛ink line position more stable.
5) 打标机维护医养时间间隔。 每60天对打标机管道阀门关闭一遍查抄，是并而不是是损坏、审议是并而不是是脱焊 改换滤过器。该使用视氛围而定，如粉层相对较大较少至少4个月时间改换一遍，寻常氛围ꦐ下予以至少12月时间关闭一遍。机械制造外部链接布袋除尘。该使用较少予以至少一个月时间关闭一遍。
5) Maintenance cycle of jet printer. Every 15 days, check the pipeline o꧒f the jet printer, whether it is ageing, whether the joints are loosened and the filters are replaced. The operation depends on the environment. If the dust is large, it should be replaced at least every four months. Normally, it should be done every 12 months. Dust removal inside the machine. The operation should be performed at least once every 1 month.
四、手持喷码机耗材类的进行和包存重视事变
IV. Notices for Use and ꦆMaintenance of 𓃲Consumables for Printers
1、喷码器采取的耗损品发挥性♚强，保留时，应最低35度，预防低温制ꩵ冷的效果，远离火源计划、供热系统，须得密封盖典范并保存在荫凉通风透气处（封杀性好的厚壁铁柜中存贮）。
1. The consumables used in the jet printer are highly volatile. They should be kept below 35 degrees, avoid high temperature and keep away from fire and heat sources. They must be well sealed and stored in a shady and ventilated place (in a thick-walled iron cಞabinet with good sealing).
2、打标机的耗损品的保存期期有的是年。
2. The shelf life of co꧃nsumables 💃of jet printer is one year.
3、激光打码(ma)机的耗损品严酷对照高端品牌采用(ᩚᩚᩚᩚᩚᩚᩚᩚᩚ𒀱ᩚᩚᩚyong)(yong)，禁止采用代替品，要不会给装配建成严重的不安全。
3. The consumables of the jet printer should be strictly used in accordance wi🌄th the brand, and no substitute should be used, otherwise𓆉 serious damage will be caused to the equipment.